We use cookies to make your experience better. To comply with the new e-Privacy directive, we need to ask for your consent to set the cookies. Learn more.
Strike Polymer FSA LITE STAB (PRE - ORDER)
$57.95
In stock
SKU
SI-FSA-SPL-STAB
Buy this product and
Earn 17.39 Reward Points click here
to login
 |
 |
 |
 |
*THIS IS A PRE ORDER*
Introducing the Strike Polymer FSA LITE STAB, built to provide a compact, lightweight stabilization option for low-recoil pistol platforms. This polymer stabilizer utilizes the TP9 locking mechanism for a secure interface, and pairs with an included picatinny rail adapter to mount across a wide range of platforms with a 1913 rail.
The body is constructed from custom high durability fiber strands, delivering exceptional rigidity in a minimal form factor. The result is a stabilizer that is extremely compact, easy to carry over long distances, and comfortable to the touch in extreme hot or cold conditions.
Installation is straightforward using the included picatinny rail adapter assembly, Torx T25 wrench, and Loctite thread locker. For B&T TP9/MP9 owners, the stabilizer mounts directly without the rail adapter.
The body is constructed from custom high durability fiber strands, delivering exceptional rigidity in a minimal form factor. The result is a stabilizer that is extremely compact, easy to carry over long distances, and comfortable to the touch in extreme hot or cold conditions.
Installation is straightforward using the included picatinny rail adapter assembly, Torx T25 wrench, and Loctite thread locker. For B&T TP9/MP9 owners, the stabilizer mounts directly without the rail adapter.
Product Specs
- Length: 10.24"
- Width: 1.67"
- Height: 4.56"
- Weight: 4.05 oz
Product Contents
*Includes the following items:*
- 1x FSA Lite Stab
- 1x FSA Lite Pic rail adapter assembly
- 1x Loctite
- 1x Torx T25 wrench
Product Features
- Lightweight Folding Stab for 1913 Picatinny Rail.
- Strong, positive lockup for quick deployment.
- Mounts directly to 1913 Picatinny rails.
- Single-side folding.
- Lightweight, low-profile design for easy carry and storage.
- High durability fiber reinforced for superior strength and stiffness.
Compatibility
- Compatible: Light weight, light recoil platforms with picatinny mounting interface. Direct mount compatible with B&T TP9/MP9.
Disclaimers & Warnings
- Always check with federal, state, and local laws. We are not lawyers and cannot provide legal advice.
- Stabilizer was designed and intended for use as a stabilizing accessory for one-handed firing with single point QD sling.
- Stock was designed and intended for use with full length rifles or registered Short-Barrel Rifles (SBR).
- Dirt and/or sand can hinder folding hinge proper operation.
- Not recommended for use while mortaring firearm to clear malfunctions.
- Expect wear and tear on folding locking mechanism from long term use.
- Be careful, avoid fingers from getting caught during folding and unfolding process.
- Picatinny interface will need ~4 sections to interface without looking out of place.
- WARNING: DO NOT INSTALL OR USE ON HIGH-RECOIL FIREARM PLATFORMS.
- RECOIL LIMIT: FOR LOW-RECOIL, RIMFIRE, PISTOL-CALIBER, AND INTERMEDIATE CARTRIDGES ONLY.
- SAFETY HAZARD: STOCK/STABILIZER COLLAPSE DURING FIRING CAN CAUSE LOSS OF CONTROL, WEAPON FAILURE, AND SEVERE INJURY.
- RISK OF UNINTENDED FOLDING: EXCEEDING RECOIL LIMITS CAN BREAK THE FRICTION FIT, CAUSING THE STOCK TO UNLATCH OR FOLD DURING LIVE FIRE.
- PRE-USE INSPECTION: ALWAYS ENSURE THE HINGE MECHANISM IS FULLY SEATED BEFORE OPERATION. DISCONTINUE USE IMMEDIATELY IF FRICTION FIT BECOMES LOOSE.
- IMPACT LIMIT: NOT INTENDED FOR MORTARING, STRIKING, OR HEAVY IMPACT.
California Proposition 65 Warning
This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information: www.P65Warnings.ca.gov
|
|
|
|
|
Upsell Products
